| MOBILE |
| Mobile module |
- 4G (LTE) – Cat 6 up to 300 Mbps, 3G – Up to 42 Mbps
|
| Status |
- Signal strength, SINR, RSRP, RSRQ, Bytes sent/received, connected band, carrier aggregation, IMSI, ICCID
|
| SMS |
- SMS status, SMS configuration, send/read SMS via HTTP POST/GET, Email to SMS, SMS to Email, SMS to HTTP, SMS to SMS, SMS auto reply
|
| USSD |
- Supports sending and reading Unstructured Supplementary Service Data messages
|
| Black/Whiles list |
- Operator black/white list
|
| Multiple PDN |
- Possibility to use different PDNs for multiple network access and services
|
| Band management |
- Band lock, Used band status display
|
| APN |
|
| Bridge mode |
- Direct connection (bridge) between mobile ISP and device on LAN
|
| WIRELESS |
| Wireless mode |
- 802.11 b/g/n, 2x2 MIMO, Access Point (AP), Station (STA)
|
| WiFi security |
- WPA3-EAP, WPA3-SAE, WPA2-Enterprise-PEAP, WPA2-PSK, WEP; AES-CCMP, TKIP, Auto Cipher modes, client separation
|
| ESSID |
|
| Wireless Hotspot |
- Captive portal (Hotspot), internal/external Radius server, SMS OTP, MAC auth, built in customizable landing page, walled garden
|
| ETHERNET |
| WAN |
- 1 x WAN port (can be configured as LAN) 10/100 Mbps, compliance with IEEE 802.3, IEEE 802.3u standards, supports auto MDI/MDIX crossover
|
| LAN |
- 1 x LAN ports, 10/100 Mbps, compliance with IEEE 802.3, IEEE 802.3u standards, supports auto MDI/MDIX crossover
|
| NETWORK |
| Routing |
- Static routes, Dynamic routes
|
| Network protocols |
- TCP, UDP, IPv4, IPv6, ICMP, NTP, DNS, HTTP, HTTPS, FTP, SMTP, SSL v3, TLS, ARP, VRRP, PPP, PPPoE, UPNP, SSH, DHCP, Telnet client, SNMP, MQTT, Wake on LAN (WOL)
|
| VoIP passthrough support |
- H.323 and SIP-alg protocol NAT helpers, allowing proper routing of VoIP packets
|
| Connection monitoring |
- Ping Reboot, Wget reboot, Periodic Reboot, LCP and ICMP for link inspection
|
| Firewall |
- Port forwards, traffic rules, NAT rules, custom rules
|
| DHCP |
- Static and dynamic IP allocation, DHCP Relay, Relayd
|
| QoS / Smart Queue Management (SQM) () |
- Traffic priority queuing by source/destination, service, protocol or port, WMM, 802.11e
|
| DDNS |
- Supported >25 service providers, others can be configured manually
|
| Network backup |
- Mobile, Wired and WiFi WAN options, each of which can be used as an automatic Failover
|
| Load balancing |
- Balance Internet traffic over multiple WAN connections
|
| SSHFS |
- Possibility to mount remote file system via SSH protocol
|
| SECURITY |
| Authentication |
- Pre-shared key, digital certificates, X.509 certificates
|
| Firewall |
- Pre-configured firewall rules can be enabled via WebUI, unlimited firewall configuration via CLI; DMZ; NAT; NAT-T
|
| Attack prevention |
- DDOS prevention (SYN flood protection, SSH attack prevention, HTTP/HTTPS attack prevention), port scan prevention (SYN-FIN, SYN-RST, X-mas, NULL flags, FIN scan attacks)
|
| VLAN |
- Tag based VLAN separation
|
| Mobile quota control |
- Custom data limits for both SIM cards
|
| WEB filter |
- Blacklist for blocking out unwanted websites, Whitelist for specifying allowed sites only
|
| Access control |
- Flexible access control of TCP, UDP, ICMP packets, MAC address filter
|
| VPN |
| OpenVPN |
- Multiple clients and a server can run simultaneously, 12 encryption methods
|
| OpenVPN Encryption |
- DES-CBC, RC2-CBC, DES-EDE-CBC, DES-EDE3-CBC, DESX-CBC, BF-CBC, RC2-40-CBC, CAST5-CBC, RC2-64-CBC, AES-128-CBC, AES-192-CBC, AES-256-CBC
|
| IPSec |
- IKEv1, IKEv2, with 5 encryption methods for IPsec (DES, 3DES, AES128, AES192, AES256)
|
| GRE |
|
| PPTP, L2TP |
- Client/Server instances can run simultaneously, L2TPv3 support
|
| Stunnel |
- Proxy designed to add TLS encryption functionality to existing clients and servers without any changes in the program’s code
|
| DMVPN |
- Method of building scalable IPsec VPNs
|
| SSTP |
- SSTP client instance support
|
| ZeroTier |
- ZeroTier VPN client support
|
| WireGuard |
- WireGuard VPN client and server support
|
| MODBUS |
| MODBUS TCP SLAVE |
| ID filtering |
- Respond to one ID in range [1;255] or any
|
| Allow remote access |
|
| Custom registers |
Modbus TCP custom register block, which allows to read/write to a file inside the router, and can be used to extend Modbus TCP slave functionality |
| MODBUS TCP MASTER |
| Supported functions |
- 01, 02, 03, 04, 05, 06, 15, 16
|
| Supported data formats |
- 8 bit: INT, UINT; 16 bit: INT, UINT (MSB or LSB first); 32 bit: float, INT, UINT (ABCD (big-endian), DCBA (little-endian), CDAB, BADC), HEX, ASCII
|
| MQTT GATEWAY |
| Gateway |
- Allows sending commands and receiving data from Modbus Master trough MQTT broker
|
| DNP3 |
| Supported modes |
- TCP Master, DNP3 Outstation
|
| DATA TO SERVER |
| Protocols |
- HTTP(S), MQTT, Azure MQTT, Kinesis
|
| MONITORING & MANAGEMENT |
| WEB UI |
- HTTP/HTTPS, status, configuration, FW update, CLI, troubleshoot, event log, system log, kernel log
|
| FOTA |
- Firmware update from server, automatic notification
|
| SSH |
|
| SMS |
- SMS status, SMS configuration, send/read SMS via HTTP POST/GET
|
| Call |
- Reboot, Status, Mobile data on/off, Output on/off
|
| MQTT |
- MQTT Broker, MQTT publisher
|
| SNMP |
- SNMP (v1, v2, v3), SNMP trap
|
| JSON-RPC |
- Management API over HTTP/HTTPS
|
| Modbus |
- Modbus TCP status/control
|
| RMS |
- Teltonika Remote Management System (RMS)
|
| IoT PLATFORMS |
| Clouds of things |
- Allows monitoring of: Device data, Mobile data, Network info, Availability
|
| ThingWorx |
- Allows monitoring of: WAN Type, WAN IP, Mobile Operator Name, Mobile Signal Strength, Mobile Network Type
|
| Cumulocity |
- Allows monitoring of: Device Model, Revision and Serial Number, Mobile Cell ID, ICCID, IMEI, Connection Type, Operator, Signal Strength, WAN Type and IP
|
| Azure IoT Hub |
- Can send device IP, Number of bytes send/received, Mobile connection state, Network link state, IMEI, ICCID, Model, Manufacturer, Serial, Revision, IMSI, SIM State, PIN state, GSM signal, WCDMA RSCP, WCDMA EC/IO, LTE RSRP, LTE SINR, LTE RSRQ, CELL ID, Operator, Operator number, Connection type, Temperature, PIN count to Azure IoT Hub server
|
| SYSTEM CHARACTERISTICS |
| CPU |
- QCA9531, MIPS 24kc, 650 MHz
|
| RAM |
|
| FLASH storage |
- 16 MB, SPI Flash (optional up to 256 MB)
|
| FIRMWARE / CONFIGURATION |
| WEB UI |
- Update FW from file, check FW on server, configuration profiles, configuration backup
|
| FOTA |
- Update FW/configuration from server
|
| RMS |
- Update FW/configuration for multiple devices at once
|
| Keep settings |
- Update FW without losing current configuration
|
| INPUT/OUTPUT |
| Configurable I/O |
- 2 x Configurable digital Inputs/Outputs. Digital input 0 - 5 V detected as logic low, 8 - 30 V detected as logic high. Open collector output, max output 30 V, 300 mA
|
| Events |
|
| I/O juggler |
- Allows to set certain I/O conditions to initiate event
|
| POWER |
| Connector |
- 4 pin industrial DC power socket
|
| Input voltage range |
- 9 - 30 VDC, reverse polarity protection, voltage surge/transient protection
|
| Power consumption |
|
| PHYSICAL INTERFACES (PORTS, LEDS, ANTENNAS, BUTTONS, SIM) |
| Ethernet |
- 2 x RJ45 ports, 10/100 Mbps
|
| I/Os |
- 2 x Configurable digital Inputs/Outputs on 4 pin power connector
|
| Status LEDs |
- 2 x Mobile connection type, 3 x Mobile connection strength, 2 x Eth status, 1 x Power
|
| SIM |
- 1 x SIM slots (Mini SIM - 2FF), 1.8 V/3 V, external SIM holders
|
| Antenna |
- 2 x SMA for LTE, 2 x RP-SMA for WiFi
|
| Power |
|
| Reset |
- Reboot/User default reset/Factory reset button
|
| PHYSICAL SPECIFICATION |
| Casing material |
- Aluminium housing with DIN rail mounting option
|
| Dimensions (W x H x D) |
|
| Weight |
|
| Mounting options |
- DIN rail, flat surface placement
|
| OPERATING ENVIRONMENT |
| Operating temperature |
|
| Operating humidity |
- 10 % to 90 % non-condensing
|
